Updated: 2022/Sep/29

Please read Privacy Policy. It's for your privacy.

ACPICPU(4)                   Device Drivers Manual                  ACPICPU(4)

     acpicpu - ACPI CPU

     acpicpu* at cpu?

     The acpicpu device driver supports certain processor features that are
     either only available via ACPI or that require ACPI to function properly.
     Typically the ACPI processor functionality is grouped into so-called C-,
     P-, and T-states.

     The processor power states, or C-states, are low-power modes that can be
     used when the CPU is idle.  The idea is not new: already in the 80486
     processor a specific instruction (HLT) was used for this purpose.  This
     was later accompanied by a pair of other instructions (MONITOR, MWAIT).
     By default, NetBSD may use either one; see the machdep.idle-mechanism
     sysctl(8) variable.  ACPI provides the latest amendment.

     The following C-states are typically available.  Additional processor or
     vendor specific states (C4, ..., Cn) are handled internally by acpicpu.

           C0  This is the normal state of a processor; the CPU is busy
               executing instructions.

           C1  This is the state that is typically reached via the mentioned
               x86 instructions.  On a typical processor, C1 turns off the
               main internal CPU clock, leaving APIC running at full speed.
               The CPU is free to temporarily leave the state to deal with
               important requests.

           C2  The main difference between C1 and C2 lies in the internal
               hardware entry method of the processor.  While less power is
               expected to be consumed than in C1, the bus interface unit is
               still running.  But depending on the processor, the local APIC
               timer may be stopped.  Like with C1, entering and exiting the
               state are expected to be fast operations.

           C3  This is the deepest conventional state.  Parts of the CPU are
               actively powered down.  The internal CPU clock is stopped.  The
               local APIC timer is stopped.  Depending on the processor,
               additional timers such as x86/tsc(9) may be stopped.  Processor
               caches may be flushed.  Entry and exit latencies are expected
               to be high; the CPU can no longer "quickly" respond to bus
               activity or other interruptions.

     Each state has a latency associated with entry and exit.  The higher the
     state, the lower the power consumption, and the higher the potential
     performance costs.

     The acpicpu driver tries to balance the latency constraints when choosing
     the appropriate state.  One of the checks involves bus master activity;
     if such activity is detected, a lower state is used.  It is known that
     particularly usb(4) may cause high activity even when not in use.  If
     maximum power savings are desirable, it may be necessary to use a custom
     kernel without USB support.  And generally: to save power with C-states,
     one should avoid polling, both in userland and in the kernel.

     The processor performance states, or P-states, are used to control the
     clock frequencies and voltages of a CPU.  Underneath the abstractions of
     ACPI, P-states are associated with such technologies as "SpeedStep"
     (Intel), "PowerNow!" (AMD), and "PowerSaver" (VIA).

     The P0-state is always the highest operating frequency supported by the
     processor.  The number of additional P-states may vary across processors
     and vendors.  Each higher numbered P-state represents lower clock
     frequencies and hence lower power consumption.  Note that while acpicpu
     always uses the exact frequencies internally, the user-visible values
     reported by ACPI may be rounded or approximated by the vendor.

     Unlike conventional CPU frequency management, ACPI provides support for
     Dynamic Voltage and Frequency Scaling (DVFS).  Among other things, this
     means that the firmware may request the implementation to dynamically
     scale the presently supported maximum or minimum clock frequency.  For
     example, if acpiacad(4) is disconnected, the maximum available frequency
     may be lowered.  By default, the NetBSD implementation may manipulate the
     frequencies according to the notifications from the firmware.

     Processor T-states, or "throttling states", can be used to actively
     modulate the time a processor is allowed to execute.  Outside the ACPI
     nomenclature, throttling and T-states may be known as "on-demand clock
     modulation" (ODCM).

     The concept of "duty cycle" is relevant to T-states.  It is generally
     defined to be a fraction of time that a system is in an "active" state.
     The T0-state has always a duty cycle of 100 %, and thus, comparable to
     the C0-state, the processor is fully active.  Each additional higher-
     numbered T-state indicates lower duty cycles.  At most eight T-states may
     be available, although also T-states use DVFS.

     The duty cycle does not refer to the actual clock signal, but to the time
     period in which the clock signal is allowed to drive the processor chip.
     For instance, if a T-state has a duty cycle of 75 %, the CPU runs at the
     same clock frequency and uses the same voltage, but 25 % of the time the
     CPU is forced to idle.  Because of this, the use of T-states may severely
     affect system performance.

     There are two typical situations for throttling: power management and
     thermal control.  As a technique to save power, T-states are largely an
     artifact from the past.  There was a short period in the x86 lineage when
     P-states were not yet available and throttling was considered as an
     option to modulate the processor power consumption.  The approach was
     however quickly abandoned.  In modern x86 systems P-states should be
     preferred in all circumstances.  It is also more beneficial to move from
     the C0-state to deeper C-states than it is to actively force down the
     duty cycle of a processor.

     But T-states have retained their use as a last line of defense against
     critical thermal conditions.  Many x86 processors include a catastrophic
     shutdown detector.  When the processor core temperature reaches this
     factory defined trip-point, the processor execution is halted without any
     software control.  Before this fatal condition, it is possible to use
     throttling for a short period of time in order to force the temperatures
     to lower levels.  The thermal control modulation is typically started
     only when the system is in the highest-power P-state and a high
     temperature situation exists.  After the temperatures have returned to
     non-critical levels, the modulation ceases.

   System Control Variables
     The acpicpu driver uses the same sysctl(8) controls for P-states as the
     ones provided by est(4) and powernow(4).  Please note that future
     versions of acpicpu may however remove these system control variables
     without further notice.

     In addition, the following two variables are available.

           hw.acpi.cpu.dynamic  A boolean that controls whether the states are
                                allowed to change dynamically.  When enabled,
                                C-, P-, and T-states may all change at
                                runtime, and acpicpu may also take actions
                                based on requests from the firmware.

           hw.acpi.cpu.passive  A boolean that enables or disables automatic
                                processor thermal management via acpitz(4).

     The acpicpu driver uses event counters to track the times a processor has
     entered a given state.  It is possible to view the statistics by using
     vmstat(1) (with the -e flag).

     acpi(4), acpitz(4), est(4), odcm(4), powernow(4), cpu_idle(9)

     Etienne Le Sueur and Gernot Heiser, Dynamic Voltage and Frequency
     Scaling: The Laws of Diminishing Returns,
     October, 2010, Proceedings of the 2010 Workshop on Power Aware Computing
     and Systems (HotPower'10).

     David C. Snowdon, Operating System Directed Power Management, School of
     Computer Science and Engineering, University of New South Wales,
     http://ertos.nicta.com.au/publications/papers/Snowdon:phd.pdf, March,
     2010, PhD Thesis.

     Microsoft Corporation, Windows Native Processor Performance Control,
     Version 1.1a, http://msdn.microsoft.com/en-us/windows/hardware/gg463343,
     November, 2002.

     Venkatesh Pallipadi and Alexey Starikovskiy, The Ondemand Governor. Past,
     Present, and Future, Intel Open Source Technology Center,
     http://www.kernel.org/doc/ols/2006/ols2006v2-pages-223-238.pdf, July,
     2006, Proceedings of the Linux Symposium.

     The acpicpu device driver appeared in NetBSD 6.0.

     Jukka Ruohonen <jruohonen@iki.fi>

     At least the following caveats can be mentioned.

        It is currently only safe to use C1 on NetBSD.  All other C-states
         are disabled by default.

        Processor thermal control (see acpitz(4)) is not yet supported.

        Depending on the processor, changes in C-, P-, and T-states may all
         skew timers and counters such as x86/tsc(9).  This is neither handled
         by acpicpu nor by est(4) or powernow(4).

        There is currently neither a well-defined, machine-independent API
         for processor performance management nor a "governor" for different
         policies.  It is only possible to control the CPU frequencies from

NetBSD 10.99                    August 31, 2018                   NetBSD 10.99